MSA-SB-2600 MILITARY SUB-ASSEMBLYHIGH EFFICIENCY ELECTRIC CONVECTION OVENINSTALLATION - OPERATION - SERVICE - PARTS44 Lakeside Avenue, Burlington, Ve
8InstallatIonControl Panel AssemblyItem Description Part No.1 Front Control Panel 98-35922 Electric Control Panel 98-36273Inner Insulation/Electric Pa
9InstallatIonControl Panel Assembly2. Attach the reed switch bracket (9), which is part of the control panel to the insulation/electric panel divide
10InstallatIonControl Panel Assembly7. Attach the high limit thermostat-mounting bracket (8) to the Frame liner support/back channel using two self-
11InstallatIonMotor Transformer AssemblyItem Description Part No.1 Motor Mount Bracket 99-39302 Motor 09-72483 Transformer 09-64754 Fan 98-35985 Motor
12InstallatIonMotor Transformer Assembly2. Place the white motor mount insulation (11) over the motor mount bracket. Tuck the left and right sides of
13InstallatIonInside Oven Cavity AssemblyItem Description Part No.1 Heating Element (480 V) 98-17772 Bafe 98-17663 Vent Tub 98-35574 Element Support
14InstallatIonInside Oven Cavity Assembly2. Install the element support bracket (4), which will be to the left of the fan, using two self-taping
15InstallatIonDoor AssemblyDoor Handle Part No. 10-0657Figure 41 Item Description Part No.1 Left Door 98-36292 Right Door 98-35893 Door Top Latch (2)
16InstallatIonOuter Skin AssemblyFigure 44 Item Description Part No.1 Side Frame Skin (2) 98-36242 Bottom U-Channel Cover 98-35853 Top U-Channel Cover
17InstallatIonOuter Skin Assembly4. Have an electrician wire a power supply line through the raceway conduit rates at 480 VAC, 3 Phase.5. Install th
TABLE OF CONTENTSINSTALLATIONIntroduction ... 2Assembly Instructions ...
18operationControl and Operating Instructions21453Figure 50 The controls required to operate the oven are listed in the following table together with
19maintenanceCleaningA good preventive maintenance program in the form of daily cleaning procedures is outlined in the following steps: 1. Remove ove
20maintenanceTroubleshootingPROBLEM Probable Cause REMEDYCONVECTOR FAN FAILS TO OPERATEPower to oven is off. Locate external circuit breaker for power
21maintenanceWiring DiagramFigure 51
22Illustrated Parts lIstRecommended Spare PartsPart No. Description Qty.10-7371 SwitchPower/Fan 110-5052 Light, Fan Power 110-5052 Light, Heating Elem
23Illustrated Parts lIstDoor Assembly with Slide LatchItem Part No. Description1A 98-3694* Kit, Door Bearing & Pin, Top & Bottom, MSA-SB-26001
24Illustrated Parts lIstItem Part No. Description1 08-7978 Fan, Cooling2 08-6472 Relay, 120 Volts3 08-6469 Fuse, Holder4 08-6552 Terminal Strip5 09-65
25Illustrated Parts lIstControl Panel with Probe OptionItem Part No. Description1 98-1717 Control Panel, Embossed2 10-7395 Buzzer3 10-5052 Light, Powe
26appendixVERIFICATION CHECK LIST1. Verify that the doors are properly aligned and that there is no interference occuring at room temperature and 400
27appendixMODEL: MSA-SB-2600SIZE: 35-1/4” Deep x 36” Wide x 25-1/4” High (896mm Front-to-Back x 914mm Wide x 641mm Top-to-Bottom) DESCRIPTION:
IMPORTANT NOTICENOTES1. Accutemp griddle mounting;This version of the Installation Manual for the Market Forge oven model MSA-SB-2600 includes the (4
28appendixPart No. Description Qty10-7371 Switch, Power/Fan 110-5052 Light, Fan Power 110-5052 Light Heating Element 108-6615 Reed, Switch 108-6472 R
29appendixPart No. DescriptionLength (inches)Thread Size Qty10-1864 SCREW CAP HEX HEAD 0.5 1/4”-20 7710-1814 SCREW CAP HEX HEAD 0.75 1/4”-20 708-7840
2InstallatIonIntroductionYOUR ENERGY EFFICIENT CONVECTION OVENMSA-SB-2600 convection ovens are electrically powered, high capacity ovens featuring
3InstallatIonAssembly InstructionsINTRODUCTIONThe model MSA-SB-2600:Submarine-Accessible Convection Oven contains 88 total parts for assembly and is d
4InstallatIonMain Frame AssemblyItem Description Part No.1 Split Base Front 98-35692 Split Base Rear 98-35683 Rear U - Channel Frame 98-35744 Front Fr
5InstallatIonMain Frame Assembly3. Bolt Rear U-channel frame (3) to split base front/ rear assembly. There are welded bolts in the corner of the spli
6InstallatIonOven Cavity AssemblyFigure 8 Item Description Part No.1 Split Liner Top 98-35762Split Liner Bottom (Has 2 Crease Lines)98-36553 U-Sh
7InstallatIonOven Cavity Assembly4. Then place another U-shaped split liner gasket (3) around the top and nish by bolting the split liner top (1) to
Commentaires sur ces manuels